Anyone have any rover 200 diesel timing photo's - Forums
Go Back Forums > Ask The Gurus! - Help and Advice Forums > Diesel Forum!

Thread Tools Rate Thread Display Modes
Old 14-02-2009, 18:38   #1
Registered User

Join Date: May 2007
Location: durham
Car: Classic Rover
Posts: 35
Anyone have any rover 200 diesel timing photo's

Hi guys i am after pictures of how to line pump timing up and engine timing thanks to check if mine is right.
maddogwhite27 is offline   Reply With Quote Quick reply to this message

Sponsored Links
Old 14-02-2009, 22:53   #2
Registered User

Join Date: May 2004
Location: Under a car near scunthorpe
Car: Maestros, 200, 600, ZTT
Posts: 24,656
Send a message via MSN to E_T_V
All the timing is done with pins so there isn't a lot to see.

If the pump pulley has been removed without locking the pump in position then you'll need specialist equipment or help to reset it.
E_T_V is offline   Reply With Quote Quick reply to this message

Old 15-02-2009, 16:18   #3
Registered User

Join Date: Apr 2007
Location: Portsmouth
Car: 45 2.0 Diesel
Posts: 7,786
it's not difficult - basically take off the top cambelt cover, and turn the crank pulley bolt until the marks on the cam sprocket and the back of the cambelt cover line up roughly. Now climb under the car and put a 6.75mm pin into the flywheel locking hole - it's below the crank sensor. Wiggle the crank pully bolt until the pin goes all the way in and the crank can no longer be turned.

Now, working in the engine bay, take off the fuel pump belt cover - you'll probably have to remove the airbox for access, and maybe the battery depending on what model. Insert a 9.5mm pin into the hole in the pump sprocket, and if it goes in further than the width of the pulley with a nice sliding fit, all is well. If it doesn't, then poke a slim screwdriver into the hole and see if you can "feel" the hole. If you cant, then remove the crank locking pin and turn the crank a whole turn until the marks line up again, and the pin goes in (this is beacuase the pump turns 180 degrees out of synch with the crank). Now repeat the process with the pump sprocket pin, if it goes in good, if it doesn't and you can find the hole near where it's supposed to be, then it's recoverable.

Undo the four slider bolts on the camshaft sprocket until the sprocket can move in the elongated holes, and then turn the sprocket with a 3/8" ratchet or breaker bar until the pump holes line up and the pin can be inserted. Now apply a torque on the camshaft sprocket until the pin becomes a nice sliding fit, and torque the 4 slider bolts up to 25NM.
Chrisund123 is offline   Reply With Quote Quick reply to this message



Quick Reply

Register Now

In order to be able to post messages on the Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Where did you hear of this site?
From which source did you hear about us?
Or enter your choice here:
What make of car do you drive?
If you have multiple cars, please use the car you drive the most. Please make sure you fill this field in as it can help others help you.
Or enter your choice here:
Your Country
Where are you from in the world!
Your Postcode (UK Only)
Please enter the first part of your postcode (i.e. WS3) This is used soley for targeting advertising, its not visible on the site, nor made available to 3rd parties. If you are not in the UK, please enter N/A
Please select your insurance company (Optional)
Any modifications to your car?
If you have made any modifications to your car, please list them here
Date of Birth
Your date of birth and age are displayed in several places on the forum. Only the administrator will have access to your date of birth should you choose to hide it via the privacy option below.
Month Day Year


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Rover 200 (1999 v) Timing help? Robbie1990 MG ZR / Rover 25, 200 & Streetwise 2 10-11-2008 21:59
timing marks on rover 200 ScotsDude MG ZR / Rover 25, 200 & Streetwise 1 30-10-2007 22:47
Rover 200 1.4 Valve Timing Mr MacPhisto MG ZR / Rover 25, 200 & Streetwise 0 10-05-2007 16:36
rover 400 diesel timing belt bigmike1962 MG ZS / Rover 45 & 400 2 28-02-2007 21:10
CAMSHAFT TIMING MARKS Rover 200 1.4 k16 john-206 Others 13 19-10-2005 18:44

All times are GMT. The time now is 14:36.

Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
ShowCase, Vendor Tools vBulletin Plugins by Drive Thru Online, Inc.